132
133
K-System (vista esplosa)
K-System (exploded view)
Constraints
The width of structures with peninsula table and/or bottle rack shelves
and/or appliances cannot be modifi ed. If a drawer and/or oven is
installed, if the structures at the side are visible they must be fi nished
with specifi c side facing panels. If a structure is next to a base unit or
cupboard composition, a side facing panel reaching down to the fl oor
must be installed between the two. The depths of structures cannot be
modifi ed. Structures cannot be confi gured with legs of different heights
and/or different depths. Fittings cannot be added and/or removed
except where specifi ed. Fittings cannot be interchanged. Multiple
module structures of 86.2 cm [33 7/8] cannot be created. Structures
cannot be placed back to back. Corner structures are not possible.
Structures cannot be used in freestanding mode. Appliances without
cabinet cannot be placed next to structures. Gas ovens, ovens with
hinged doors or ovens requiring ventilation from the top cannot be
used. Only the specifi c side facing panels can be fi xed to structures.
At the end of the composition, it is not possible to add cupboard top
boxes d 35 cm [13 3/4] on structures d 40 cm [15 3/4] or cupboard top
boxes d 60 cm [23 5/8] on structures d 70 cm [27 1/2]. "Small" depth
worktops cannot be used. Any type of worktop can be applied on
structures h 76 cm [29 7/8], but specifi c hobs and/or washing zones
can only be added with DUAL. The DUAL worktop cannot be applied
on structures h 87 cm [34 1/4], and hobs and sinks cannot be added;
only special washing zones can be used. To allow correct installation
of structures, the following room dimensional requirements must be
met. There must always be a gap of at least 1 cm [3/8] above the top
of the structure. If the structure is installed in an alcove, there must
be a gap of at least 1 cm [3/8] widthways. If the structure is installed
between two walls, there must be a gap of at least 8 cm [3 1/8]
widthways. The room must always be at least 100 cm [39 3/8] deeper
than the length of the structure.
Characteristics
K-System structures are confi gured in single or multiple modules and
can be installed on walls (d 40 [15 3/4] - 60 [23 5/8] - 70 cm [27 1/2])
[or in island mode (d 40 [15 3/4] - 60 cm [23 5/8]) in line with specifi c
base units, to form only d 120 cm [47 1/4]. If the rear panels are larger
than the maximum producible sizes, they will be produced in two or
more parts. The bottom level is always fi tted with a fi xed shelf or a
tubular footrest (only base structure h 76 [29 7/8] - 87 cm [34 1/4] d
40 cm [15 3/4]). The intermediate levels, shown by the broken lines,
can be fi tted with fi xed or removable shelves. If hobs and/or washing
zones are installed, electricity and/or water connections must be
provided as shown in the technical diagrams in the price list.
Feasibility
The width of the base unit structures can be modifi ed (from 45 [17 3/4]
to 125 cm [49 1/4]) and so can those of the tall unit structures (from
45 [17 3/4] to 120 cm [47 1/4]) with a few exceptions. The height of
the variable height structures only can be reduced and the positions of
the shelves above the drawer can be modifi ed provided the interspace
between two shelves is no less than 18 cm [7 1/8]. The second level
can be equipped with removable aluminium shelf with glass/bottle
rack or with solid wooden shelf, as preferred. Wooden shelves can
be fi tted with LED lighting strips from a minimum height of 119 cm
[46 7/8] and cornices from a minimum height of 186 cm [73 1/4]. The
rear panel may be wider in order to cover the thickness of any side
facing panels. Wall unit and cupboard top boxes can be placed on
top of the structure. Structures h 76 [29 7/8] - 87cm [34 1/4] p 60 cm
[23 5/8] may be placed 10 cm [3 7/8] from the wall to allow the use of
worktops d 70 cm [27 1/2], provided the sides are not visible, meaning
that they are next to a side facing panel, a wall or a corner cupboard.
The tall unit back panel can be fi tted with an electrifi ed rail. Structures
can be customised in the Metallix fi nishes and the lacquered fi nishes of
the K-Lab programme. Structure back panels can be customised in the
wood fi nishes and the lacquered fi nishes of the K-Lab programme.