Vario gas wok 400 series
V G 415
V G 415 115F
Stainless steel.
Width 38 cm.
Liquid gas 28–37 mbar.
Wok burner with up to 5.8 kW.
Knob needs to be ordered separately.
V G 415 215
Stainless steel.
Width 38 cm.
Natural gas 20 mbar.
Wok burner with up to 6 kW.
Knob needs to be ordered separately.
Included in the price
1 wok attachment ring.
Necessary Installation accessories
CKG 410 010
Stainless steel knob 400 series
for VG 415.
Electronic control.
Set of 1 knob.
CKG 410 000
Black knob 400 series for VG 415.
Electronic control.
Set of 1 knob.
Installation accessories
V A 420 004
Connection strip for combination with
other Vario appliances of the
400 series for flush mounting.
V A 420 010
Connection strip for combination with
other Vario appliances of the
400 series for surface mounting.
V A 440 010
Stainless steel appliance cover with
mounting strip.
Special accessories
W P 400 001
Wok pan made of multiple-layer
material.
With round bottom and handle,
ø 36 cm, 6 litres, height 10 cm.
Highlights
— Multi-ring burner with up to 6 kW.
— Full electronic power level
regulation on 12 levels.
— Solid stainless steel knob, also
selectable with black robust
finishing, for precise control and
personalisation.
— Precision crafted 3 mm stainless steel.
— For surface mounting with a visible
edge or for flush mounting.
— Precise and reproducible flame size.
— Automatic fast ignition, electronic
flame monitoring with automatic
re-ignition.
— Simmer function for cooking on a
very low output level.
— Can be combined perfectly with
other Vario appliances of the
400 series.
Cooking zones
VG415115F
1 multi-ring wok burner
(300 W–5800 W), suitable for pots
up to max. ø 32 cm.
VG 415 215
1 multi-ring wok burner
(300 W–6000 W), suitable for pots up
to max. ø 32 cm.
Handling
Control knobs with illuminated ring,
cooking zone and output level
markings.
One-handed operation.
Full electronic control in 12 output
levels for exact power level regulation
plus simmer function.
Automatic fast ignition.
Features
Simmer function.
Cast iron pan support with flat,
continuous pot surface.
Brass burner rings.
Safety
Electronic flame monitoring with
automatic re-ignition.
Residual heat indication.
Safety shut-off.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover),
the specific location of the cut-out
and the knob positions may vary.
The drawing "Installation of the
control knob" must be observed if the
panel is more than 23 mm thick (there
must be a recess at the rear).
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The bearing capacity and stability, in
the case of thin worktops in
particular, must be supported using
suitable substructures. Take into
account the appliance weight and
additional loads.
Additional instructions for flush
mounting:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop
manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
Please read additional planning notes
on page 132–136.
If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Special nozzles can be ordered as
spare parts.
Plan for an electrical connection (the
appliance is not operable without
power supply).
Air intake from above.
No intermediate shelf required.
Rear panel and wall trims must be
heat-resistant and consist of a
non-flammable material.
A minimum clearance of at least
150 mm from adjacent heat-sensitive
furniture or contact surfaces must be
observed or thermal insulation fitted.
If operated next to the downdraft
ventilation VL 414, the ventilation
moulding AA 414 is recommended to
ensure maximum performance of the
cooktop.
With a total connected load of more
than 11 kW local regulations
concerning room ventilation, room
size and combination of extraction or
recirculation hoods must be observed.
The minimum distance between the
cooktop surface and a cabinet above,
out of combustible material, needs to
be 70 cm.
The minimum distance to a ventilation
above is shown at the planning hints
for the individual ventilation product.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 15 kg.
Connection
Total connected load gas 5.8/6.0 kW.
Total connected load electric
15.0/15.0 W.
Connecting cable 1.4 m with plug.
Connecting cables 0.3 m and 1 m for
control knobs.
Vario cooktops
122
