Lighting system with diffuse unilateral or bilateral
emission, with high-performance LED light sources.
Light emission is obtained by the combination
of six monochromatic LED light sources,
a reflector and an opaline diffuser.
Floor, wall or recessed installation.
Available in two finishes:
light grey painted and rust painted.
Ciclope floor
Available in unilateral and bilateral emission
version and in two heights (h 50cm and h 90cm).
Stem in extruded EN AW-6060 aluminium.
Lighting unit composed by:
frame in reinforced polymer;
diffuser in light-diffusing polycarbonate;
plate in pickled, machined and galvanized steel;
watertight gasket in silicone rubber;
LED circuit;
electronic ballast;
reflector in painted spun aluminium;
PG13.5 cable gland, H05RN-F cable and IP65
electrical connection device suitable for cables with
a diameter between 6 and 13 mm and allowing
the electrical interfacing with the external mains
without need of opening the fixture.
The lighting unit houses the electrical components
and sources.
Aesthetic cover in die-cast EN AB-47100 aluminium.
Ground mounting plate in folded, welded
and painted steel, with holes for ground fixing
by means of log bolts or dowels.
The elements are fixed together by means of screws.
All the locking screws used outside the fixture
and inside the stem are in AISI 304 stainless steel.
The components in die-cast, extruded aluminium
and steel are painted by means of 3-stage outdoor
treatment: nanotechnologies, antioxidant primer,
polyester paint.
Technical features of light fixtures in compliance
with EN60598-1.
IP Rating IP65.
ENEC approved.
Insulation class II.
Ciclope wall
Box in extruded EN AW-6060 aluminium.
Lighting unit composed by:
frame in reinforced polymer;
diffuser in light-diffusing polycarbonate;
plate in pickled, machined and galvanized steel;
watertight gasket in silicone rubber;
LED circuit;
electronic ballast;
reflector in painted spun aluminium;
PG13.5 cable gland, H05RN-F cable and IP65
electrical connection device suitable for cables
with a diameter between 6 and 8.5 mm
and allowing the electrical interfacing with
the external mains without need of opening
the fixture.
The lighting unit houses the electrical components
and sources.
Aesthetic cover in die-cast EN AB-47100 aluminium.
The elements are fixed together by means of screws.
All the locking screws used outside the fixture
and inside the stem are in AISI 304 stainless steel.
The components in die-cast, extruded aluminium
and steel are painted by means of 3-stage outdoor
treatment: nanotechnologies, antioxidant primer,
polyester paint.
Technical features of light fixtures in compliance
with EN60598-1.
IP Rating IP65.
ENEC approved.
Insulation class II.
Ciclope recessed
Lighting unit composed by:
frame in reinforced polymer;
diffuser in light-diffusing polycarbonate;
plate in pickled, machined and galvanized steel;
watertight gasket in silicone rubber;
LED circuit;
electronic ballast;
riflettore in alluminio tornito in lastra e verniciato
PG13.5 cable gland, H05RN-F cable and IP65
electrical connection device suitable for cables
with a diameter between 6 and 8.5 mm
and allowing the electrical interfacing with
the external mains without need of opening
the fixture.
The lighting unit houses the electrical components
and sources.
Aesthetic cover in die-cast EN AB-47100 aluminium
painted by means of 3-stage outdoor treatment:
nanotechnologies, antioxidant primer,
polyester paint.
Recessing box in reinforced polymer,
can be ordered separately.
The elements are fixed together by means of screws.
All the locking screws used outside the fixture
and inside the stem are in AISI 304 stainless steel.
Technical features of light fixtures in compliance
with EN60598-1.
IP Rating IP65.
ENEC approved.
Insulation class II.
201
