530
531
SURGE PROTECTION DEVICE
For Class I y Lighting Fixtures
For Class II q Lighting Fixtures
Outdoor Lighting fixtures are subject to many different types of temporary, transitional or permanent electrical disturbances. Such disturbances can create permanent
damage or failure that can jeopardize the performance or lifetime of the fixtures. Surge protection devices are utilised to limit the damage of such electrical
disturbances. Each fixture must be connected to one single device at a distance of no more than 10m away.
A correct protection system against overvoltage or voltage spikes must also provide for the installation of a surge protection device inside the mains electrical
switchboard (the selection of this device is the responsibility of the electrician or electrical contractor).
SURGE PROTECTION DEVICE 10kV
Compatible with all lighting fixtures classified
under electrical Protection Class I y
Rated voltage 230-277V
SPD type 2+3
Max Surge Protection 10kV
IP67
SURGE PROTECTION DEVICE 10kV
Compatible with all lighting fixtures classified
under electrical Protection Class II q
Rated voltage 230-277V
SPD type 2+3
Max Surge Protection 10kV
IP67
DALI RELAY SWITCH for ON-OFF (not dimmable) 230V LUMINAIRES
All not dimmable (ON-OFF) 230V devices can be controlled ON-OFF with the DALI system using the following interface accessories. As a result, the
luminaires will be remotely controllable in ON-OFF mode only and not in dimmed mode.
DALI RELAY SWITCH IP67
Max nominal load 1000VA
Max switching current 8A
Max inrush current 80A
Dimensions 175,5mm x86,5mm x43mm
DALI RELAY SWITCH IP20
Max nominal load 1000VA
Max switching current 8A
Max inrush current 80A
Dimensions 32,5mm x15mm x58,5mm
IP20 Independent
IP rated Box
SIGNAL CONVERTER FOR DIMMABLE LUMINAIRES
These signal converter can convert the dimmable signal in different protocol: from PUSH DIM to DALI2, from DALI to PHASE-CUT or from DALI to
VIRTUAL MIDNIGHT.
INTERFACE from DALI to PHASE-CUT IP20
Maximum power consumption 230W
Max switching current 1A
Dimensions 80mm x40mm x24,5mm
INTERFACE from PUSH DIM to DALI2
IP20
Allowed powering up to 35 DALI-2 interface
in BROADCAST
Dimensions 43mm x43mm x18,5mm
INTERFACE from DALI to VIRTUAL
MIDNIGHT IP20
Module for automatic power reduction
/ brightness reduction for night-time.
The device has an integrated bus supply
(20mA) for up to 7 DALI luminaires.
Dimensions 60mm x33mm x15mm
DALI EXPANDER 64 LUMINAIRES IP20
The DALI Expander has an integrated
DALI bus power supply (200mA) which
can control up to a maximum of 64 DALI
devices within 300 meters.
INTERFACE from DALI to VIRTUAL
MIDNIGHT IP67
Module for automatic power reduction
/ brightness reduction for night-time.
The device has an integrated bus supply
(20mA) for up to 7 DALI luminaires.
Dimensions 175,5mm x86,5mm x43mm
INTERFACE from DALI to VIRTUAL MIDNIGHT +
EXPANDER UP TO 64 LUMINAIRES IP67
Module for automatic power reduction / brightness reduction
for night-time. The device has an integrated bus supply
(20mA) for up to 64 DALI luminaires.
Dimensions 272,5mm x102mm x43mm
DALI
VIRTUAL MIDNIGHT
PHASE-CUT
CONNECTORS FOR THROUGH WIRING
3 Way connector
4 Way connector
Where the lighting fixtures are equipped with power supply cable, these accessories are employed for carrying-out a loop in, loop out wiring connection. These
connectors can be installed in junction boxes, inside recessing boxes (inground / wall products) or inside the posts of the bollards. Verify the installation
compatibility of each lighting fixture by visiting our website.
3 WAY CONNECTOR
for cables up to 3x1,5mm²
diam. min 7mm / max 12mm
IP68
3 WAY GEL CONNECTOR
for cables up to 5x1,5mm²
diam. min 6,5mm / max 12mm
IP68
4 WAY GEL CONNECTOR
for cables up to 3x2,5mm²
diam. min 6,5mm / max 12mm
IP68
4 WAY GEL CONNECTOR
for cables up to 4x1,5mm²
diam. min 6,5mm / max 12mm
IP68
S.2496
S.2495
S.2491
S.2493
S.2497
S.2490
S.2492
S.2494
S.2498
S.5504
S.5507
S.2499
S.5506
S.5519
