V G 491 111F
Stainless steel
Width 90 cm
Liquid gas 28 – 37 mbar
V G 491 211
Stainless steel
Width 90 cm
Natural gas 20 mbar
Included in the price
1 wok attachment ring
Installation accessories
V A 420 004
Connection strip for combination with
other Vario appliances of the
400 series for flush mounting
V A 420 010
Connection strip for combination with
other Vario appliances of the
400 series for surface mounting
Special accessories
W P 400 001
Wok pan made of multiple-layer material
With round bottom and handle,
ø 36 cm, 6 litres, height 10 cm.
Combinable with:
Ceiling ventilation 400 and 200 series
Table ventilation 400 series
Island- and wall-mounted hood 400 series
Flat kitchen hood 200 series
Canopy extractor 200 series
Good to know:
the hood has to be larger than the
cooktop(s) or it has to be as large as
the cooktop(s). Please check the
requirements in chapter ventilation.
Vario gas cooktop 400 series
V G 491
–
Five multi-ring burners, up to 18 kW
–
Full electronic power level
regulation on 12 levels
–
Precise and reproducible flame size
–
Automatic fast ignition, electronic
flame monitoring with automatic
re-ignition
–
Simmer function for cooking on a
very low output level
–
Solid smooth-surface cast iron pan
supports
–
Solid stainless steel control knob
–
Precision crafted 3 mm stainless
steel
–
For surface mounting with a visible
edge or for flush mounting
–
Can be combined perfectly with
other Vario appliances of the
400 series
Cooking zones
VG 491 111F
1 multi-ring wok burner
(300 W – 5800 W), suitable for pots up
to max. ø 32 cm.
2 two-ring high output burners
(165 W – 4000 W), suitable for pots up
to max. ø 28 cm.
2 two-ring standard burners
(165 W – 2000 W), suitable for pots up
to max. ø 24 cm.
VG 491 211
1 multi-ring wok burner
(300 W – 6000 W), suitable for pots up
to max. ø 32 cm.
2 two-ring high output burners
(165 W – 4000 W), suitable for pots up
to max. ø 28 cm.
2 two-ring standard burners
(165 W – 2000 W), suitable for pots up
to max. ø 24 cm.
Handling
Control knobs with illuminated ring,
cooking zone and output level markings.
One-handed operation.
Full electronic control in 12 output
levels for exact power level regulation
plus simmer function.
Automatic fast ignition.
Features
Simmer function.
Three-part cast iron pan support with
flat, continuous pot surface.
Brass burner rings.
Safety
Electronic flame monitoring with
automatic re-ignition.
Residual heat indication.
Safety shut-off.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
The horizontal positioning of the knobs
may be aligned with the specific
burners.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 23 mm thick (there must be
a recess at the rear).
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush mounting:
Installation is possible in worktops
made of stone, synthetics or solid wood.
Heat resistance and watertight sealing
of the cut edges must be observed.
Concerning other materials please
consult the worktop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
Please read additional planning notes
on page 132 – 136.
If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Special nozzles can be ordered as
spare parts.
Plan for an electrical connection
(the appliance is not operable without
power supply).
Air intake from above.
No intermediate shelf required.
Rear panel and wall trims must be
heat-resistant and consist of a
non-flammable material.
A minimum lateral clearance of at least
300 mm from adjacent heat-sensitive
furniture or contact surfaces must be
observed or thermal insulation fitted.
Installation in a 90 cm wide lower
cabinet is required.
The combination with VL 414 is not
recommended, since the air extraction
from the centre burner cannot be
guaranteed due to the distance.
With a total connected load of more
than 11 kW local regulations
concerning room ventilation, room size
and combination of extraction or
recirculation hoods must be observed.
Minimum clearance between gas
cooktop(s) with more than 11 kW and
ventilation hood 70 cm.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 32 kg.
Connection
Total connected load gas
17.8/18.0 kW.
Total connected load electric
15.0/15.0 W.
Connecting cable 1.4 m with plug.
