V I 462 103
Frameless
Width 60 cm
Installation accessories
V A 420 004
Connection strip for combination with
other Vario appliances of the
400 series for flush mounting
Special accessories
G P 900 001
Stainless steel frying sensor pan
Non-stick coating, ø 15 cm.
G P 900 002
Stainless steel frying sensor pan
Non-stick coating, ø 19 cm.
G P 900 003
Stainless steel frying sensor pan
Non-stick coating, ø 21 cm.
G P 900 004
Stainless steel frying sensor pan
Non-stick coating, ø 28 cm.
Combinable with:
Ceiling ventilation 400 and 200 series
Table ventilation 400 series
Island- and wall-mounted hood 400 series
Flat kitchen hood 200 series
Canopy extractor 200 series
Good to know:
the hood has to be larger than the
cooktop(s) or it has to be as large as
the cooktop(s). Please check the
requirements in chapter ventilation.
Flex induction cooktop 400 series
V I 462
–
Flex function for combining the
rectangular cooking areas
–
Free positioning of cookware inside
combined cooking areas with
automatic extension up to 30 cm
width
–
Frying sensor function for
temperature control in pans
–
Easy control of all functions with
bicoloured display
–
Solid stainless steel control knob
–
Frameless for flush mounting
Cooking zones
2 flex induction cooking areas 20x23 cm
(2200 W, with booster 3700 W),
linked together 40x23 cm (3300 W,
with booster 3700 W),
with automatic extension up to 30x30 cm
(3300 W, with booster 3700 W).
2 flex induction cooking areas 20x23 cm
(2200 W, with booster 3700 W),
linked together 40x23 cm (3300 W,
with booster 3700 W).
Handling
Control knobs with illuminated ring,
cooking zone and output level markings.
Electronic power control in 12 output
levels.
User friendly control with bicoloured
display (white / orange).
Features
Flex function for rectangular cooking
areas.
Frying sensor function.
Booster function.
Stopwatch.
Short-term timer.
Options menu.
Power management.
Cooktop-based ventilation control
(with suitable hood).
Home network integration for digital
services (Home Connect) wireless
via WiFi.
The use of the Home Connect
functionality depends on the Home
Connect services, which are not
available in every country. For further
information please check:
home-connect.com.
Please read additional information on
Home Connect on page 416.
Safety
Operation indicator.
Pot detection.
2-stage residual heat indication.
Safety shut-off.
Planning notes
The horizontal positioning of the knobs
may be aligned with the specific
cooking areas.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 23 mm thick (there must be
a recess at the rear).
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Installation is possible in worktops
made of stone, synthetics or solid wood.
Heat resistance and watertight sealing
of the cut edges must be observed.
Concerning other materials please
consult the worktop manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Operates with magnetic (induction)
iron pots and pans only. For an optimal
heat distribution, the use of sandwich
bottom cookware is recommended.
The wok pan WP 400 001 cannot be
used with this appliance.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 18 kg.
Please read the installation details
regarding air ducting on page 204.
Connection
Total connected load 7.4 kW.
Connecting cable 1.5 m without plug.
